The SmartGen controller is designed for use with generator automation and monitoring. Before the benefits of this high quality product can be used, it must be correctly connected.
Dingbo Product Page
The system is relatively easy to install. The communication lines need to be connected to the system, the installation programme downloaded and the controller configured. It is then good to go.
The wiring is connected to the controller terminals using pull-apart terminal blocks.
The unit is then mounted to panel front with 2 fixing clamps. Before the AC power is connected, ensure that the mains matches the SmartGen’s power supply factory settings.
The software can be installed. It is best not to connect the controller to the PC via the USB cord before the software has been installed.
Open the installation file which is supplied on a disc with the device. Follow the instructions to launch the wizard and follow the prompts until the download is complete.
Connect the front panel USB port to the computer. Follow all prompted instructions to complete the installation.
Before connecting to the SmartGen controller, the software should be configured in correct communication mode.
If you are looking for more details, kindly visit SmartGen controller manufacturer.
The SmartGen controller uses 32-bit microprocessor technology. It fits with an SAE J1939 port. This port can communicate with multiple ECU (Engine Control Unit) units. It connects the genset connected to the internet. After the controller is logged in a cloud server, it can upload the data information at real-time to the corresponding cloud server.
The majority of parameters can be set using the front panel and all the parameters can be set using a PC (through a USB port)
When using a PC to change or set the parameters, it is done through the software that was installed. There are different options within the menu that provide the required settings or configuration.
Alternatively, this can be done via the front panel. Pressing the required buttons allows the parameter setting mode. The security code is inputted and the parameter table will open. This then allows the user to make the necessary changes.
Once the desired parameter changes are complete, simply press the exit parameter button to complete the process.
Your GenSet controller is now ready for use.
For more details about connecting a SmartGen Controller, speak to Generator Power Solutions today or shop online for a SmartGen Controller.
DESCRIPTION:
HGM1780 is a genset automatic start module with 3 working modes that can be selected from the front panel. It can detect one-phase generator voltage and current, can be started and stopped manually or via a remote start/stop signals. In case of faults (such as low oil pressure, high water/cylinder temperature, emergency stop alarm, over speed), HGM1780 can automatically disconnect fuel relay and close ETS electromagnet to stop the generator. Graphical LCD monitor on the front panel displays fault conditions and provides effective alarm signals.
PERFORMANCE AND CHARACTERISTICS:
- Based on microprocessor, fitted with LCD screen with graphic icons and touch-buttons;
- Power supply range (8~35)VDC，compatibility with 12V or 24V starter batteries;
- Generator input port; speed, temperature, pressure, liquid level sensor input ports; digitalized electric quantity display.
- Generator voltage, battery voltage, engine speed, temperature, pressure, liquid level threshold value can be set.
- Idle control and ETS function (must be configured);
- 3 working modes: manual, auto, stop;
- The controller can be set as an engine controller via software (generator voltage input is deactivated) and used as water pump unit controller;
- Running status and alarm status are indicated by red LED on the panel;
- Compatibility with multiple temperature, pressure, fuel level sensors, which can be user-defined and used directly; temperature sensors, pressure sensors can be used in parallel with annunciator, providing digital data and increasing protection level at the same time;
- Multiple crank disconnect conditions to select (engine speed sensor, oil pressure, generator);
- 2 fixed relay outputs (fuel relay, start relay);
- 1 configurable output port which can be set as common alarm output, fail to stop output, preheat output or idle control output;
- Parameters can be set and modified by users and saved in internal FLASH storage, which means that they will not be lost in case of power off. All parameters of the controller can be modified using the front panel or through configurable LINK port via PC software (SG72 adapter, produced by our company must be used). All parameters can be set via computer using one USB port of the computer, which also allows to avoid batteries: power supply for the controller can come directly from the PC USB port.
- HGM1780 combines modular design, anti-flaming ABS plastic case, embedded installation, compact structure, small size, SCM control, stable performance and convenient operation.
TECHNICAL SPECIFICATIONS:
Display Icon-LCD
Operation Panel PET
Digital Input 2
Relay Output 3
Analogue Input 3
AC System 1P2W
Alternator Voltage (15~360)V(ph-N)
Alternator Frequency 50/60Hz
Programmable Interface LINK
DC Supply DC(8-35)V
Case Dimensions(mm) 90*78*44
Panel Cutout(mm) 78*66
Operating Temp. (-25~+70)℃
The company is the world’s best what causes high oil pressure in a diesel engine supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.