Rural fencing is tough, durable and has many different uses &#; whether it be fencing paddocks for animal control, creating a perimeter for your land, or even just a boundary for your veggie patch.
Want more information on star pickets exporter? Feel free to contact us.
Installing a rural fence doesn&#;t need to be difficult &#; but you do need to be diligent in planning it out and undertaking the works.
Once you&#;ve designed the layout of your fence on paper, you need to determine how much of each type of material you will need to construct the fence.
One of the key components of your rural fence will be star pickets &#; they&#;re available in a wide range of sizes as well as a hi-vis version, and are built to withstand harsh conditions.
Some of these will be strainer posts, and you&#;ll also need strainer post stays, a post driver and galvanised tie wire.
The following steps outline basic instructions on how to build a star picket fence.
Once you&#;ve planned out where your fence will go, you&#;ll need to prepare the area. Clear long grass, sticks and branches, and consider the location of nearby waterways, contours of the land and the soil type.
These posts are the backbone of your fence and will take the load of the tensioned wire &#; if they fail, then your whole fence will follow. Make sure you&#;re setting them in deep enough so your posts won&#;t pull out under pressure; the deeper they are set in, the greater their load capacity.
You can drive the post in using a heavy-duty post driver, or by digging a hole and backfilling it.
Once the strainer posts are in the ground, you can install the stays &#; remember, when it comes to stay lengths, they should generally be at least 2.5 times the height of your fence.
Strain a wire close to the ground between your strainer posts &#; this will be your guide. Lay out your star pickets at even spaces, and make sure it&#;s straight!
A good rule of thumb for spacing is your pickets is about one every four meters &#; anything more than five meters will make for a weak fence that is difficult to tension.
Now that your star pickets are laid out in the right place, it&#;s time to drive them into the ground.
Use a post driver to take the hard work out of installing the star pickets &#; when the picket is positioned, place the driver over the top and use downward pressure to drive the post into the ground.
Your star pickets should be 600mm deep into the ground, so make sure when planning your fence, you account for this with the height of your star pickets.
If you accidentally drive your star pickets into the wrong spot, a star picket remover will make the removal process a lot easier than if you try to pull it out by hand.
Attach one end of your wire to your strainer post, then run it through your star pickets to the strainer at the other end. Using a wire strainer will make this an easier process and will assist with making sure your wires are appropriately tensioned.
Make sure you over-tension the wire slightly, as you will lose some tension when tying off. You can tie off using a gripple or twisting tool, or if you&#;re confident you can tie off with a figure-eight knot or a slip knot.
Your final step is to attach the wires to the star pickets and strainer posts. This helps keep the wire secure. Run one wire under the line wire and the other over the line wire to keep it in place, or simply use a fence post clip. And there you have it, your star picket fence is complete!
TTFS has a range of star pickets for sale along with other fencing accessories. We have built a solid reputation for always providing a high-quality product, backed up by competitive pricing, fantastic customer service and product guarantees.
With depots in Melbourne, Sydney, Perth, Adelaide and Brisbane, we can deliver Australia-wide within 24 hours direct from our factory. For any enquiries, contact the TTFS team by sending an enquiry, emailing [ protected] or calling 119 998
Star Pickets are widely used in construction sites, vegetable gardens, boundary lines and farms. Here we&#;d like to introduce necessary tools for star picket installation and installation steps in farms.
Prepare the material you need.
Before proceeding with the installation, we need to get necessary accessories well prepared. Our commonly used accessories include post pullers, post drivers, post clips, metal wires, barbed wiers and fence fields.
If you want to learn more, please visit our website galvanized steel mesh roll manufacturing.
Post puller
Made of zinc-impregnated steel, it provides a maximum 10 cm lift with each pull, and ensures it can remove fence posts that need to be replaced easily. The anti-rust powder coating protect the puller from corrosive elements. It is mainly used for replacing star pickets.
Post driver
It is made of a section of hollow steel pipe with one end closed and the one end open like a sleeve. In addition, it has handles on both sides to allow your hands hold on and operate the puller easily. First put the puller on the top of the star picket and then you can install the y post with minimum effort, making the installation simple, time-saving, safe and reliable.
Post clips
There are a variety of post clips. It is mainly used for the fixation between metal wire, barbed wire, field fence and star picket to form a closed farm. It enjoys a long service life and excellent corrosion resistance performance.
Metal wires, barbed wires, fence stays & field fence
Metal wires, barbed wires, fence stays and field fences are used to connect star pickets together to form a closed structure to prevent animals from entering or running out and protect crops from destroying.
Y post puller
Y post driver
Post clips for star picket connection
Metal wire
Barbed wire
Fence stays
Field fence
Install Y posts.
Metal wire installation
Make the metal wire pass through the star picket fixing holes and secure it with post clips. If you want to keep metal wires straight, you may add a fence stay vertically in the middle part. Some wire fences are equipped with barbed wires at the top of the wire fence or alternatively used with barbed wire. Barbed wire installed must be fixed with post clips.
Field fence installation
First, place the field fence in a proper position along the star picket. And then make post clips pass through star picket prepared holes and secure with field fence. Generally, a barbed wire is added to the top of the field fence. Stretch the barbed wire , place it in the top notch and then secure the barbed wire with post clips.
Metal wire installation
Field fence installation
It can be seen that the installation of y post is very simple and convenient as long as we master the correct method. We are a professional fence post manufacturer. We can provide not only y posts, but also t posts, round posts, square posts and peach shape posts for you to choose from. We have fence posts that are suitable for many applications. If you are looking for fence posts, please contact us immediately. We will offer you the most suitable and economical fence posts for your application to help you save your time and budget.
Inquiry for Our Product
Hebei Jinshi Industrial Metal Co., Ltd.
:
When you contact us, please provide your detail requirements. That will help us give you a valid quotation.
For more information, please visit concertina wire pickets manufacturer.