Please visit our website for more information on this topic.
Electrolytic tinplate containers are frequently lacquered to provide additional protection and/or to enable thinner tin coatings to be used.For internal can surfaces, a lacquer must provide an inert barrier between the metal of the container and its contents, and must not convey any odour or taint to the food and drink coming into contact with it. Important properties required in all lacquers include an ability to spread evenly, completely over tinplate surfaces, which have received no special pre-treatment, and to adhere to the surfaces under what may be adverse conditions.
For processed food cans, any external coating or decoration system must be capable of withstanding subjection to steam / water mixtures for periods up to approximately one hour at temperatures in the range 120 &#; 132°C . Historically virtually all lacquers have been solventbased, containing up to 80% solvent in the wet state. Over recent years, many of these have been replaced by water-based materials, which contain 10 &#; 15% solvent and are therefore more environmentally friendly. Many types of lacquer are now in general use and new or modified formulations are continually being introduced.
Oleoresinous
Oleoresinous types are still much used in the U.S.A. for cans for packaging fruit and vegetables, but are not widely employed in Europe.They are based on natural products, so that the composition may vary somewhat, but they are cheap.They are not very effective against sulphide staining unless pigmented with zinc oxide. They dry by oxidation and by thermal polymerisation.
Vinylic
Vinylic types are vinyl copolymers, reinforced by thermoplastic resins. Principal qualities include adherence, flexibility (useful in deep drawing applications) and lack of taint. This type is not very temperature resistant; it dries by evaporation of solvent.Vinylic lacquers are often used as second coats, for example on beer and beverage cans or biscuit tins, where lack of odour or taint is important. They cure at 170 &#; 175°C , to avoid thermal degradation in contact with steel at pores.
Phenolic
Phenolic resins give good coverage and have excellent chemical resistance. They are impermeable to sulphide ions and will resist the heat of soldering. A limitation is the sensitivity of their adherence properties to the surface condition of the tinplate and their low flexibility in coatings thicker than 3-4µm. Phenolics cannot be heated above 190°C without degradation; drying occurs by heating. Vinyls and phenolics are often used in combination for optimum properties.
Organosols
Organosols are vinylic resins of high molecular weight dispersed in solvent mixtures, to give, typically, 55% dry solids. By fusion, at the time of heating the resins form a thick (10 &#; 20µm) continuous film. They are often used inside cans, for bases of aerosols or on beer cans or DRD cans. Acrylics are particularly used where high heat resistance and colour retention is needed. They are used for exterior decoration and increasingly in recent years as a white coating for food cans, where they give an attractive ceramic appearance.
Epxoy phenolics lacquers
Epxoy phenolics lacquers are the most widely used types. They have good resistance to acid products and the epoxy component confers adherence and flexibility. They are cured at about 200°C . A wide range of formulations are commercially available, differing in ratios of the two resins.They are used in cans for packing soups, meats, fish, fruits and fruit juices, and internally and externally on crown corks and other closures. They are suitable for deep drawing. Certain formulations resist the action of polyphosphates which can reduce the adherence of phenolics, and they can be pigmented with aluminium or with zinc carbonate to counteract sulphide staining.
Other epoxy based materials have had a major impact in the market place in recent years. Concern over Volatile Organic C ompound (VOC ) emissions has been a driving force to reduce the level of organic solvents present in coatings systems and this has led to the introduction of water based epoxy acrylate emulsions which now play a major role within the beer and beverage market. More recent developments in terms of improved flexibility have extended the use of these materials into the food can market. Requirements for improved performance white internal coatings have led to the development of solvent based epoxy anhydride based systems.
However, recent concerns over the environmental impact of epoxy based systems, including epoxy phenolics, has led to pressures within the industry to review the use of bisphenol A and bisphenol F based materials. Although no definite evidence supporting these concerns has materialised, it is likely that polyester and acrylic based polymer systems may well become more widely used in the future as replacements for epoxy materials in certain applications.
Except for D&I cans, virtually all lacquering and decorating of tinplate is applied to flat sheets, prior to the forming operations. The coatings are applied via a roller system, as described below, and then enter a stoving oven. They are taken on a continuous conveyor which carries the sheets vertically on edge through a tunnel oven, which has a series of temperature controlled zones. The actual temperatures and total stoving times depend on the curing requirements of the particular coating.Temperatures must be below the melting point of tin, and for this reason a maximum of 205°C is normally never exceeded. Time at peak metal temperature is of the order of 10 minutes. At the exit of the stoving oven the cured sheets are stacked on pallets. They may require several stages of lacquering and/or decorating, necessitating several stoving treatments. Some plants have installed lines for continuous lacquering of tinplate coil: on these high-speed lines the melting point of tin may be momentarily exceeded.
The decoration of tinplate requires the printing of coloured designs on the surface.Tinplate has an excellent surface for printing and in this respect is superior to many high quality papers. However, there are certain fundamental differences between printing on tinplate and printing on paper. In the first place tinplate is non-absorbent, so that ink or lacquer remains on the surface and has to be dried by the application of heat or other form of energy.
With competitive price and timely delivery, Steelhighsen sincerely hope to be your supplier and partner.
Secondly, the metal has a hard inflexible surface compared to paper, so that direct contact between printing plate and the tinplate surface is not practicable. Thirdly, in terms of its spectral response, tinplate can be considered as being essentially black: this means that if reproduction similar to that achieved on white paper is required, a white base must first be applied to the metal surface. However, for special decorative effects, use may be made of the surface appearance of the tinplate itself. Another important fact to be borne in mind is the functional nature of the printed tinplate which is subsequently formed into various shapes, to be used as containers or other items. Coatings must remain adherent and undamaged even after forming operations which may involve quite severe deformation of the surface.
The tinplate surface makes possible a wide diversity of colour effects when used in conjunction with the range of opaque and transparent printing inks available and the printing process itself has evolved to allow the precise registration of fine detail at high line speeds.The decorating process consists of two operations; roller coating and printing. A number of coatings may be applied to tinplate before printing and a final overvarnish coating may also be applied after printing.
Printing on tinplate is not only for decorative purposes, but the creative and appealing design of a packaged product is vitally important for its sales potential and this is especially true for the large range of foods, beverages and household products marketed in cans. Although many food cans use separately applied paper labels, the use of labels printed directly onto the can is increasing and is already universal for beer and beverage cans. Printed tinplate has a variety of other uses including battery cases, trays, large container tins (for sweets, biscuits, etc.), bottle caps, ash-trays, and advertising signs.
Source: The International Tin Association (formerly ITRI Ltd)
Scan Holdings is a competitive and leading exporter for Printed and lacquered Tinplate that is used in the manufacturing of metal Cans and Lids/Bottoms for packaging of food, beverage drinks, paint and aerosol.
With almost 30 years&#; experience in Tinplate/TFS Can & End Making technology, Scan Holdings understands the importance of high-quality tinplate, high lacquer integrity (quality) and precision lithographic with exact colour matching. So many of our customers prefer to directly buy lacquered and printed tinplate/TFS from us and avoid the administrative hassles and cost of first buying tinplate and later sending them to an agency for printing and/or lacquering.
For a different type of usage, Scan Holdings can recommend you the right type of tinplate and appropriate lacquer. It can also participate to improve your products visual appeal by making suggestions on lithography. And of course, it can exactly follow and deliver the lacquer and printing specification if the buyer wants no changes.
Scan Holdings can offer:
ETP (Electrolytic Tinplate)
It is Low carbon steel coated with tin having a layer between them of steel-tin alloy and destined to be used mainly in the production of metal cans and lids. Tinplate provides good weldability and electrical conductivity, as well as high corrosion resistance.
Tinplate can be supplied in sheets or coils. In the case of sheets, we are able to deliver the material lacquered and printed, as well as with straight or scroll cut. The thickness offered by us is from 0.14mm to 0.30mm. We can offer both single reduced (SR) and double reduced (DR) tinplate. The hardness (temper) can be as per customer requirement. Both Batch Annealed (BA) and Continuous Annealed (CA) can be offered. Tin Coating can be same or differential on outside and inside as per client&#;s requirement.
Double reduced (DR) ETP is normally thinner but stronger than conventional Single Reduced (SR) ETP. DR ETP is produced by electrolytic coating of tin on steel, which after an initial cold reduction and annealing is subjected to a second cold reduction with lubrication, which gives work hardening effect and imparts additional strength to Double Reduced material.
In addition to DR Tinplate, we can also offer Soft Double Reduced Electrolytic Tinplate (Soft DR ETP). Soft DR ETP is Double Reduced material produced with lower second cold reduction as compared to the normal DR ETP with a hardness/temper of 65+4/-3. Soft DR is available in thickness ranging from 0.18 to 0.23 mm.
Tinplate (ETP): What we offer &#; at a glance! Tin Coating Starting from E05 to E100. More common coatings are D2.8/1.12 (D25/10), 2.8/2.8 (E25), 5.6/5.6 (E50), 5.6/2.8 (D 50/25), D 11.2/5.6 (D 100/50). Differential tin coating on inside and outside are offered too. Hardness (Temper) T-1 (49 ± 5); T-2 (53 ± 5); T-2.5 (55 ± 5); T-3 (57 ± 5); T-S (59 ± 5); T-4 (61 ± 5); T-5 (65 ± 5); DR-8 (73± 5); DR-9 (76 ± 5); Annealing Batch Annealed (BA) and Continuous Annealed (CA) Finish Stone, Matt, Bright Thickness 0.14mm to 0.30mm Lacquer Type Epoxy, Polyester, Aluminium suitable for a variety of products like meat, pet food, fish, tomato, vegetables, fruits, Cheese etc. Lacquering can be done in different shades of Gold, Clear/Transparent, White and Buff. Special lacquers offered for Cheese packing. Lithography / Printing Offered with both conventional and UV sheet printing technology. Special effects can be given by using metallic and temperature sensitive inks.
Common Uses for tinplate offered by us are in:
&#; Edible Oils
&#; Paints
&#; Aerosol
&#; Battery Components
&#; Processed foods
Tin Free Steel (TFS)
Tin Free Steel (TFS): What we offer &#; at a glance! Hardness (Temper) T-1 (49 ± 5); T-2 (53 ± 5); T-2.5 (55 ± 5); T-3 (57 ± 5); T-S (59 ± 5); T-4 (61 ± 5); T-5 (65 ± 5); DR-8 (73± 5); DR-9 (76 ± 5); Annealing Batch Annealed (BA) and Continuous Annealed (CA) Finish Stone, Matt, Bright Thickness 0.14mm to 0.30mm Lacquer Type Epoxy, Polyester, Aluminium suitable for a variety of products like meat, pet food, fish, tomato, vegetables, fruits, Cheese etc. Lacquering can be done in different shades of Gold, Clear/Transparent, White and Buff. Special lacquers offered for Cheese packing. Lithography / Printing Offered with both conventional and UV sheet printing technology. Special effects can be given by using metallic and temperature sensitive inks.
An advantage in Buying from Scan Holdings
By buying from us you can have the following benefits:
1. Competitive Cost. Especially for lacquered and/or printed tinplate and TFS.
2. High Quality of tinplate.
3. Precision Printing.
4. High lacquer integrity.
5. Expert recommendation/suggestion using more than 30 years of experience available with us.
6. Saving in administrative & handling cost by the buyer in comparison to separately arranging tinplate, printing & lacquering activities
The company is the world’s best lacquered tinplate supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.